Quick Tip: Tuning Your Foscam Motion Detection
If you’re using your IP camera as a monitoring tool that’s saving videos (or images) when motion takes place, then you will want to spend some time adjusting your camera’s motion detection settings. This means ensuring the available settings are optimized for the particular scene where motion needs to be captured. If you don’t adjust these settings, you’ll probably be left with a large amount of recordings that can make it difficult or tedious to review at a later date (not to mention the increased storage and bandwidth costs).
Most IP cameras provide some decent settings that allow you to customize what triggers motion and a subsequent recording. Here’s a simple example that shows you how to tune a Foscam FI9821P to capture people approaching a front step.
First, assess what kind of motion you want to capture. In this scene, the only motion that needs to be recorded is a human approaching the front step. You will also want to consider what could trigger a lot of false alarms. Any outdoor scene is always susceptible to wind motion and with several trees and other plants in this scene, we’ll need to figure out a way to ignore those and just zero-in on the area where a person would walk.
To do this on the Foscam, simply go to Settings -> Alarm -> Motion Detection. (Note: be sure you have installed their browser plug-in otherwise this menu won’t be available. The camera’s login screen provides a link to download the plug-in.)
From here, select Set Detection Area. This will open up a view of your scene overlaid with a red grid. This is where you assign areas of the scene where you want motion detection to be active (or disabled).
To ensure wind from the trees and plants are ignored, as well as vehicles passing by on the street, the entire area outside of the interlocking bricks has been de-selected. This will ensure only motion activity in the red grids will initiate a recording, greatly reducing the amount of video stored while ensuring only relevant events are saved.
The final step was to set motion sensitivity to a relatively low value — in this case a setting of “Medium” is appropriate. You could likely even go lower since a person would be a large object in this scene, so it’s highly likely the motion detection would trigger. You’ll probably need to play with the settings a bit to get the right sensitivity.
Most mid-range IP cameras and up have this kind of functionality, so I encourage you to take the time to tune your settings. You’ll be thankful in the end… and if you’re looking for an IP camera cloud storage service for all those recordings, give Camcloud a try – we have a free plan available and several paid plans that offer large amounts of cloud storage.
LarryPosted at 23:03h, 29 March
Exactly what I needed to know, thank you sir! Will bookmark and should I need your service in the future, I will definitely consider you.
Marwan AlshafeiPosted at 18:28h, 01 April
JanPosted at 12:15h, 10 May
I have trouble getting the motion area saved. After I have saved it, (with the OK button) it will change the aerea. It looks like it falls back to some default.
Cam UserPosted at 16:33h, 16 August
The Camera Motion Detection area settings are sufficient. However, once the Camera was added to CamCloud, my configured Motion Detection area was overwritten by cam cloud settings and then i started receiving false motion detected events. then i paid for the Upgrade thinking i might get better options for the MD area configuration. but that didn’t happen. am i missing something here?
I get one big red square and thats it, but thats not sufficient for my requirements. The Settings available in the camera (with smaller, multiple squares) is what i want.
if this is not possible now, is this on the roadmap?
or if not, then any possible way to have the Camera Settings the preferred?
Cam UserPosted at 16:35h, 16 August
P.S: The Red Square is resizable, but this does not meet requirements.
WendyPosted at 18:17h, 24 December
Thank you for this. I had the masking completely backwards. I’m thinking that the red xxx maskng would be the don’t record area.
NogeroPosted at 00:07h, 08 March
One would think marking an area with a red “X” should mean “do not include”, but logic escapes Foscam programmers.
The other bummer is if you just disable motion detection it erases the detection area data. So if you re-enable you have to set detection area over again.
BobuSPosted at 11:30h, 17 May
When I switch motion detection on and gives area where it should be detected my NVR start sending me mail during whole day. I only need that possibility to be on during non-working hours. Is it possible to set it on ZXtech Mini DVR?
doNObuyFOSCAMipCAMPosted at 05:27h, 08 June
DO NOT BUY A FOSCAM CAMERA ! Their support is the worst that I have experiences my whole life !
RaresPosted at 08:59h, 26 September
Is it possible after the motion detection triggers on the output alarm switch , the switch to turn off automaticly after a certain time ?
Jon van den BoogaertPosted at 13:38h, 21 December
The button to set the motion detection area is gone!
Where can I find it now?
BobPosted at 23:58h, 25 February
I would like to know this also. I was thinking the browser is the issue and I need an old version of some browser to get it back. Who knows how to fix this issue?